SGI InfiniteStorage 4000 Series Betriebsanweisung Seite 73
- Seite / 122
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Replacing a Failed Environmental Status Module
007-4834-001 55
Replacing a Failed Environmental Status Module
When TPSSM instructs you to replace a failed environmental status module, read
“Environmental Status Modules (ESMs)” on page 19, and then follow the steps in this
section.
Caution: Electrostatic discharge can damage sensitive components. Use a grounded
wrist strap or other antistatic precautions before handling enclosure components.
1. Check TPSSM for instructions on environmental status module failure recovery
procedures. Follow any instructions provided before you proceed.
2. Unpack the new environmental status module. Set the new module on a dry, level
surface near the enclosure. Save all packing materials in case you need to return the
module.
3. Review all documentation shipped with the new environmental status module for
updated replacement procedures and other information. If necessary, modify the
remaining steps to meet the system requirements. Kits often contain the most
current servicing information. If the kit instructions conflict with those in this
procedure, follow the kit instructions.
4. Locate the failed environmental status module (its fault indicator should be on).
5. Disconnect the Fibre Channel cables from the SFP transceivers in the failed module,
and then remove the SFP transceivers (see “Replacing an SFP Transceiver” on
page 51). Label each cable to ensure that all cables are properly reconnected to the
new module.
Caution: Bending or damaging Fibre Channel cables can result in degraded
performance or data loss. Fibre Channel cables are fragile. Do not pinch the cables
with tie wraps, step on them, or bend at them at sharp angles.
6. Wearing antistatic protection, push down on the latch centered above the
environmental status module. The levers will pop out of the locked position (see
Figure 4-8).
7. Grasp the pull-rings and pull on the levers to remove the failed module.
8. Wearing antistatic protection, slide the new environmental status module all the
way into the empty slot.
!
!
- InfiniteStorage™ 4000 RAID 1
- User’s Guide 1
- Record of Revision 3
- Contents 5
- 007-4834-001 vii 7
- About This Guide 13
- Important Information 14
- Chapter Descriptions 14
- Related Publications 15
- Conventions 16
- Product Support 16
- Reader Comments 17
- System Features 19
- 2 007-4834-001 20
- Performance Features 21
- RAID Controller Features 22
- Availability Features 23
- Supported Platforms 23
- System Components 24
- Storage Enclosures 25
- 8 007-4834-001 26
- 007-4834-001 9 27
- 10 007-4834-001 28
- 007-4834-001 11 29
- 2. Storage Enclosures 31
- Overview 33
- 16 007-4834-001 34
- 2: Storage Enclosures 34
- The Disk Drives 35
- RAID Controllers 35
- 18 007-4834-001 36
- Power Supply and Fan Modules 38
- Tray ID Selection 39
- Link Rate Switch 40
- SFP Transceivers 40
- 007-4834-001 23 41
- Figure 2-9 SFP Transceiver 41
- Turning the Power On 43
- 26 007-4834-001 44
- 007-4834-001 27 45
- 28 007-4834-001 46
- 007-4834-001 29 47
- Turning the Power Off 48
- 007-4834-001 31 49
- Checking the Indicator Lights 50
- Rear Indicator Lights 52
- 36 007-4834-001 54
- Moving the Enclosure 55
- Removing the Enclosure 56
- 007-4834-001 39 57
- Reinstalling the Enclosure 58
- Front Bezel Air Filter 59
- 42 007-4834-001 60
- Replacing a Failed Disk Drive 61
- 44 007-4834-001 62
- 007-4834-001 45 63
- 46 007-4834-001 64
- Alarm Mute button on the 64
- 007-4834-001 47 65
- 48 007-4834-001 66
- 007-4834-001 49 67
- Figure 4-5) 68
- Replacing an SFP Transceiver 69
- 52 007-4834-001 70
- 54 007-4834-001 72
- 007-4834-001 55 73
- 56 007-4834-001 74
- Upgrading Drives 75
- 58 007-4834-001 76
- 007-4834-001 59 77
- 60 007-4834-001 78
- Adding Expansion Enclosures 79
- 62 007-4834-001 80
- 5. Cabling 81
- 64 007-4834-001 82
- 007-4834-001 65 83
- 007-4834-001 73 91
- 74 007-4834-001 92
- 007-4834-001 75 93
- 76 007-4834-001 94
- 007-4834-001 77 95
- 78 007-4834-001 96
- 007-4834-001 79 97
- 80 007-4834-001 98
- Powering On the System 99
- 82 007-4834-001 100
- 5: Cabling 100
- Rack Specifications 101
- Rack Dimensions 102
- 007-4834-001 85 103
- Rack (empty) 104
- Each system 104
- 007-4834-001 87 105
- Area Requirements 106
- Wiring and Power 107
- Power Requirements 108
- Power Distribution Units 108
- Power Cords and Receptacles 108
- 007-4834-001 91 109
- Environmental 110
- Enclosure Specifications 111
- System Enclosure Air Flow 115
- Electromagnetic Emissions 117
- Product Safety 118
- Electrostatic Discharge 118
- Shielded Cables 119
- FCC Warning 119
- VDE 0871/6.78 120
- European Union Statement 120
- Attention 121
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern