SGI InfiniteStorage 4000 Series Betriebsanweisung Seite 69
- Seite / 122
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Replacing an SFP Transceiver
007-4834-001 51
8. Slide the new controller into the empty slot, and close the latch.
9. Reconnect the SFP transceivers and the host interface cables to the controller.
10. Turn on the power, and wait for the drives to spin up.
11. Check the power and fault indicators on the new controller as follows (see
Figure 4-4 on page 50):
• If the power indicator is off, the controller module may not have been inserted
correctly. Remove the module and reinsert it.
• If the fault indicator is on, the power indicator stays off, or any other fault
indicator is on, use TPSSM to determine the problem.
12. Did reinstalling the unit correct the problem?
• Yes – Go to step 16.
• No – Contact your Technical Support Organization.
13. Complete any remaining Recovery Guru procedures, if needed.
14. Using the lights and the storage management software, check the status of all the
trays in the storage array.
15. Does any component have a Needs Attention status?
• Yes – Click the Recovery Guru toolbar button in the Array Management Window,
and complete the recovery procedure. If a problem is still indicated, contact your
Customer Support Organization.
• No – Go to step 16.
16. See TPSSM for instructions on bringing the RAID controller online.
17. The replacement is complete, create, save, and print a new storage array profile.
Replacing an SFP Transceiver
Use the following procedure to replace a Small Form-factor Pluggable (SFP) transceiver
on the drive tray. The SFP transceiver shown in this procedure might look different from
those you are using, but the difference does not affect transceiver performance. You need
antistatic protection and a replacement SFP transceiver for this procedure.
- InfiniteStorage™ 4000 RAID 1
- User’s Guide 1
- Record of Revision 3
- Contents 5
- 007-4834-001 vii 7
- About This Guide 13
- Important Information 14
- Chapter Descriptions 14
- Related Publications 15
- Conventions 16
- Product Support 16
- Reader Comments 17
- System Features 19
- 2 007-4834-001 20
- Performance Features 21
- RAID Controller Features 22
- Availability Features 23
- Supported Platforms 23
- System Components 24
- Storage Enclosures 25
- 8 007-4834-001 26
- 007-4834-001 9 27
- 10 007-4834-001 28
- 007-4834-001 11 29
- 2. Storage Enclosures 31
- Overview 33
- 16 007-4834-001 34
- 2: Storage Enclosures 34
- The Disk Drives 35
- RAID Controllers 35
- 18 007-4834-001 36
- Power Supply and Fan Modules 38
- Tray ID Selection 39
- Link Rate Switch 40
- SFP Transceivers 40
- 007-4834-001 23 41
- Figure 2-9 SFP Transceiver 41
- Turning the Power On 43
- 26 007-4834-001 44
- 007-4834-001 27 45
- 28 007-4834-001 46
- 007-4834-001 29 47
- Turning the Power Off 48
- 007-4834-001 31 49
- Checking the Indicator Lights 50
- Rear Indicator Lights 52
- 36 007-4834-001 54
- Moving the Enclosure 55
- Removing the Enclosure 56
- 007-4834-001 39 57
- Reinstalling the Enclosure 58
- Front Bezel Air Filter 59
- 42 007-4834-001 60
- Replacing a Failed Disk Drive 61
- 44 007-4834-001 62
- 007-4834-001 45 63
- 46 007-4834-001 64
- Alarm Mute button on the 64
- 007-4834-001 47 65
- 48 007-4834-001 66
- 007-4834-001 49 67
- Figure 4-5) 68
- Replacing an SFP Transceiver 69
- 52 007-4834-001 70
- 54 007-4834-001 72
- 007-4834-001 55 73
- 56 007-4834-001 74
- Upgrading Drives 75
- 58 007-4834-001 76
- 007-4834-001 59 77
- 60 007-4834-001 78
- Adding Expansion Enclosures 79
- 62 007-4834-001 80
- 5. Cabling 81
- 64 007-4834-001 82
- 007-4834-001 65 83
- 007-4834-001 73 91
- 74 007-4834-001 92
- 007-4834-001 75 93
- 76 007-4834-001 94
- 007-4834-001 77 95
- 78 007-4834-001 96
- 007-4834-001 79 97
- 80 007-4834-001 98
- Powering On the System 99
- 82 007-4834-001 100
- 5: Cabling 100
- Rack Specifications 101
- Rack Dimensions 102
- 007-4834-001 85 103
- Rack (empty) 104
- Each system 104
- 007-4834-001 87 105
- Area Requirements 106
- Wiring and Power 107
- Power Requirements 108
- Power Distribution Units 108
- Power Cords and Receptacles 108
- 007-4834-001 91 109
- Environmental 110
- Enclosure Specifications 111
- System Enclosure Air Flow 115
- Electromagnetic Emissions 117
- Product Safety 118
- Electrostatic Discharge 118
- Shielded Cables 119
- FCC Warning 119
- VDE 0871/6.78 120
- European Union Statement 120
- Attention 121
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.225 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern